Baby blankets are a timeless newborn or baby shower gift, particularly ones that are handmade. Beautiful yet practical, a hand-knit baby blanket is a gift that is cherished. There is nothing quite like gifting or receiving something that has had time and love put into creating it. Baby blankets are also wonderfully beginner friendly so even if you’re new to knitting you can still create a special hand-knit gift.
If you know the name of the baby then a personalised baby blanket, such as this square Stitch & Story one, is a lovely touch. However, often a gift is required before the name, or gender, are known (such as for a baby shower) in which case you can’t go wrong with simple striped blankets in neutral colours. The Stitch & Story Stripey Blankie and Sophie la girafe: Sleepy Baby Blanket are popular choices. Using our signature super soft The Lil’ Merino, and with easy-to-follow patterns, these kits produce beautiful blankets that can be passed down through generations.
While knitting colour block stripes is fun, weaving in the tail ends where you change colour can be less so. The patterns for both the Stripey Blankie and Sophie la girafe: Sleepy Baby Blanket detail the colour changing method of cutting your working yarn and attaching new yarn at each block, before weaving in. Below we’ve outlined a way you can weave the different coloured yarn up through your work as you knit without having to cut or reattach your yarn, or weave in lots of tail ends when you’re finished.
1. After you’ve completed the required rows in your first colour (Colour A) simply pick up the strand from your next ball of yarn (Colour B) and, leaving about a 10cm tail end, begin knitting your next row. You do not need to knot or attach the new yarn to the old. Don’t worry if the first couple of stitches seem loose; you will weave in the tail end when you have finished knitting which will tighten and secure these stitches.
2. Knit two rows in Colour B, bringing you back to the edge where Colour A is still attached. Before starting your third row lift Colour A’s yarn strand in front of and over Colour B’s yarn strand.
3. Begin knitting your third row in Colour B. You will notice that Colour A’s yarn strand has been lifted up two rows along the edge of your work.
4. Knit another two rows (row three and four). Again lift Colour A’s yarn strand in front of and over Colour B’s yarn strand, before starting your next (fifth) row.
5. Continue in this way, lifting the yarn every two rows, until you have completed the required number of rows in Colour B.
TIP - Avoid pulling tightly on the yarn strands you are lifting up and weaving along the edge of your work otherwise your edge will pucker and be uneven. Make sure there is enough give along the edge of the previous colour block before you start the first row of your next.
6. In the same way that you added a second colour, simply pick up the strand from your next ball of yarn (Colour C) and, leaving about a 10cm tail end, begin knitting your next row.
7. Knit two rows in Colour C, bringing you back to the edge where both Colour A and Colour B are still attached. This time, before starting your third row, lift both Colour A’s and Colour B’s yarn strands in front of and over Colour C’s yarn strand.
8. Begin knitting your third row in Colour C. You will notice that both Colour A’s and Colour B’s yarn strands have been lifted up two rows along the edge of your work.
9. Continue in this way, lifting the yarn every two rows, until you have completed the required number of rows in Colour C.
10. When you are ready to change colours again, all three yarn strands will be available to you at the correct side of your work. Just remember to lift the strands for the two colours you are not knitting with in front of and over your working yarn every second row.
11. When you have finished, and cast off, cut all your yarn strands leaving approximately 10cm and weave these ends (and those from when you first added a new colour) back into your work. You can read our blog on weaving in ends here.
You can use the above method to add and alternate between multiple colours (not just three) and experiment with how frequently you change colours - opting for thinner or thicker stripes.
TIP - This method of ‘carrying the yarn along the edge’ of your work only applies to patterns where there is an even row repeat, i.e. the colour changes every 2, 4, 6, etc. rows. This method does not work for knitting patterns that change colour every row or after an odd number of rows, where yarn will need to be joined on both sides of the work.
The images above relate to the Stripey Blankie whose colours are alternated evenly across the blanket. With the Sophie la girafe: Sleepy Baby Blanket this method is perfect for the two colours alternating in the main section of the pattern but you may prefer to cut and reattach the yarn colour used just on either end, as outlined in the pattern.
While this method of changing yarns doesn’t entirely do away with weaving in at the end, it does significantly reduce the amount of ends you’re left with to weave in - particularly if you’re working with multiple colours or are changing colour frequently in a pattern. As well as saving time you’re left with neat edges, which is preferable when making a blanket where there are no seams to hide knots or tail ends. For tips on how to weave in ends you can read our blog post here.
Stripes and colour blocking in a blanket are a great way to make a project more fun to knit and look really impressive despite being very easy to do. If you’d love to knit a baby blanket but are completely new to knitting, the Stitch & Story baby blankets are beginner level kits and super easy to make. The kits come with everything you need to get started, including a How to KNIT basic guide, and as always if you get stuck you can reach out to our very helpful customer services team. All you’ve got to decide is which lucky baby is getting your hand-knit blanket.
Comments will be approved before showing up.